Description:This oil extractor transfer pump uses 12v mini self-priming pump to exchange car engine oil(for engine lubricating oil only). It works by connecting the clamps to the 12V car-battery,and widely used in general industrial equipment, cause this pump can pump oil not only, also can pump hydraulic oil and other liquid. It is an ideal equipment for quick and clean oil-changes.1.Widely used in general industrial equipment.2.It works by connecting the clamps to the 12V car-battery.3.An ideal equipment for quick and clean oil-changes.4.Simple on/off power switch, easy to use.Specification:Rated Voltage: DC 12VRated Power: 60WMaximum Pressure: Max. 0.8MPAMaximum Flow: 5L/minPump Diameter: Approx. 4.8cm / 1.89″Length: Approx. 14.5cm / 5.7″Outlet Pipe Size(Dia.*L): Approx. 11mm*140cm / 0.43″ * 55″Inlet Pipe Diameter: Approx. 8mm & 6 mm / 0.31″ & 0.24″Inlet Pipe Length: Approx. 100cm / 39.37″Cable Length: Approx. 30cm / 11.8″Clips Length: Approx. 8cm / 3.15″Main Color: BlackApplication: Widely used in general industrial equipment, medical equipment, chemical equipment, shipbuilding, drinks, carpet and floor cleaning, water purification and water treatment equipment, vehicle cleaning, agricultural spraying, zo pipeline pressure, air cleaning cooling, coal and metallurgical industries.How to use:1.Start to run the car engine for a while, when oil temperature turns to be about 50 degrees, start pumping oil.2.Connect the pump to the power, run it for a while, and observe whether the inlet and outlet is normal.3.Open the filler cap,get dipstick out, force the tube into the bottom of the joint, until the tube does not move; then put the inlet pipe from the oil dipstick into in end (the tube into the bottom of the tank, the bottom concave place, in order to pump the oil completely); as no oil or pumping up very slowly or intermittently, it is generally caused by loose pipes and fittings. You have to install the pipes and fittings again.)4.After oil pumping, remove the tube, and then run the pump for a while, pump the remaining oil inside the pumping clean, or pump water for a while until the pump head gets clean.5.If you have not used it for a long time, it may have no suction, then just pour the water in the pump, and run the pump for a few minutes until the air is all out.Package Included:1 X Oil Pump1 X 11mm Outlet Pipe1 X 8mm Inlet Pipe1 X 6mm Inlet Pipe2 X Clips
12V 60W Oil Fluid Liquid Extractor 5L Boat Car Auto Transfer Pump Change Kit AP
$62.10
Weight | 1.92 lbs |
---|---|
MPN | 1185704 |
Be the first to review “12V 60W Oil Fluid Liquid Extractor 5L Boat Car Auto Transfer Pump Change Kit AP” Cancel reply
Related products
Automobiles & Motorcycles
Engine Kill Starter Button Switch Motorcycle Pit Dirt Bike ATV Quad
Automobiles & Motorcycles
Automobiles & Motorcycles
Heater Blower Motor Resistor For BMW Final Stage E39 E46 X5 1997-2006
Automobiles & Motorcycles
12V Regulator Rectifier Voltage Motorcycle Aluminum Fit For Ducati 1098 848 1198
Automobiles & Motorcycles
Motorcycle Speedometer Tachometer Odometer Rev Counter 0-13000 RPM
Automobiles & Motorcycles
12V Intank Fuel Pump For Kawasaki Ninja ZX6R 1995 1996 1997 1998 1999 2000 2001
Automobiles & Motorcycles
34mm 55mm Intake Carburetor 2 Stroke Racing Flat Side Part Carb Dirt Bike ATV Motorcycle 300cc
Automobiles & Motorcycles
Lawn Mower Recoil Pull Start Starter Assembly For Tecumseh 590420A 590706 16575
Reviews
There are no reviews yet.